|
03-09-2019, 01:37 AM | #1 |
Private
5
Rep 60
Posts |
Torque specs for the attached??
I'm trying to install a racechip unfortunately the do not have vehicle specific instructions fir the F02.
So in attempting I think the best way is to remove the bars in the attached picture. I don't know the proper name for the bars but I believe it gives the car more stiffness. Anyway I don't know if I I should just tighten pretty snug or if there is a specific torque they should bet tightened any help would be appreciated!!! |
03-09-2019, 12:24 PM | #2 |
Enlisted Member
5
Rep 32
Posts |
|
Appreciate
0
|
03-09-2019, 01:49 PM | #3 | |
Private
5
Rep 60
Posts |
Quote:
|
|
Appreciate
0
|
03-10-2019, 11:02 AM | #4 |
Enlisted Member
5
Rep 32
Posts |
newTIS.infobeta
Home / BMW F02 760Li Sedan / Repair Manuals and Technical Data / 64 Heating and air conditioning / 64 53 Condenser and dryer with lines / 51 61 Reinforcement, body Tightening Torques Type Thread Tightening specifications Torque 1AZ Suspension cross-brace in engine compartment, rear F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M10x47 Renew screws Jointing torque 30 Nm Angle of rotation 90 ° F15 / F16 Renew screws Jointing torque 25 Nm Angle of rotation 90 ° F25 / F26 M10x25 Renew screws Jointing torque 56 Nm Angle of rotation 90 ° 2AZ Suspension cross-brace in engine compartment, front F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M10x25 56 Nm F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M10x47 Renew screws Jointing torque 30 Nm Angle of rotation 90 ° 3AZ Connection, rear, to carrier support F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 28 Nm 4AZ Connection, front, to connection, rear F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 19 Nm 5AZ Engine compartment lid catch F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M8x20 11,8 Nm 6AZ V-support to connection, front F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 19 Nm 7AZ Air duct, lower, to vertical strut F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 19 Nm 8AZ Air duct, lower, to carrier F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M8 8 Nm 9AZ Air duct, upper, on lock support F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M8 8 Nm 10AZ Trailing link/V-strut on side member F07 / F11 / F12 / F13 M12 Renew screws Jointing torque 100 Nm Angle of rotation 90 ° 11AZ Trailing link to compression strut, rear axle F07 / F11 / F12 M8 19 Nm 12AZ Trailing link to cross reinforcement (rear end support) F07 / F11 / F12 M12 Renew screws Jointing torque 100 Nm Angle of rotation 90 ° 13AZ Cross reinforcement (support, rear end) to rear end F07 / F11 / F12 M10x22 38 Nm 14AZ Cross reinforcement (support, rear end) to cross-member F07 / F11 / F12 M10 38 Nm 15AZ Torsion struts/stiffening plate to front axle support F01 / F02 / F03 / F12 M10 Renew screws Jointing torque 56 Nm Angle of rotation 90 ° 16AZ Rear trailing link F10 / F12 M10x40 Renew screws Jointing torque 56 Nm Angle of rotation 105 ° 17AZ Rear trailing link F10 / F12 M8x35 Renew screws Jointing torque 28 Nm Angle of rotation 90 ° |
Appreciate
0
|
03-10-2019, 11:05 AM | #5 |
Enlisted Member
5
Rep 32
Posts |
|
Appreciate
0
|
03-11-2019, 12:11 AM | #6 | |
Private
5
Rep 60
Posts |
Quote:
|
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|