BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   7Post - 7 Series Forum > BMW 7-Series Forums > General 7-series (F01) Discussion

Post Reply
 
Thread Tools Search this Thread
      03-09-2019, 01:37 AM   #1
cowboy750
Enlisted Member
cowboy750's Avatar
United_States
0
Rep
37
Posts

Drives: bmw F02 750LI,E84 X1
Join Date: Apr 2018
Location: salinas,ca

iTrader: (0)

Torque specs for the attached??

I'm trying to install a racechip unfortunately the do not have vehicle specific instructions fir the F02.
So in attempting I think the best way is to remove the bars in the attached picture. I don't know the proper name for the bars but I believe it gives the car more stiffness. Anyway I don't know if I I should just tighten pretty snug or if there is a specific torque they should bet tightened any help would be appreciated!!!
Attached Images
 
Appreciate 0
      03-09-2019, 12:24 PM   #2
beach48
Enlisted Member
4
Rep
32
Posts

Drives: 2013 F02 760LI
Join Date: Nov 2016
Location: Bristol UK

iTrader: (0)

https://www.newtis.info/tisv2/a/en/

Put details in here to get what your after
Appreciate 0
      03-09-2019, 01:49 PM   #3
cowboy750
Enlisted Member
cowboy750's Avatar
United_States
0
Rep
37
Posts

Drives: bmw F02 750LI,E84 X1
Join Date: Apr 2018
Location: salinas,ca

iTrader: (0)

Quote:
Originally Posted by beach48 View Post
https://www.newtis.info/tisv2/a/en/

Put details in here to get what your after
Thanks for that link but I need the the actual name to the part and that I'm not sure of...
Appreciate 0
      03-10-2019, 11:02 AM   #4
beach48
Enlisted Member
4
Rep
32
Posts

Drives: 2013 F02 760LI
Join Date: Nov 2016
Location: Bristol UK

iTrader: (0)

newTIS.infobeta
Home / BMW F02 760Li Sedan / Repair Manuals and Technical Data / 64 Heating and air conditioning / 64 53 Condenser and dryer with lines /
51 61 Reinforcement, body
Tightening Torques
Type Thread Tightening specifications Torque
1AZ
Suspension cross-brace in engine compartment, rear
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M10x47 Renew screws
Jointing torque 30 Nm
Angle of rotation 90
F15 / F16 Renew screws
Jointing torque 25 Nm
Angle of rotation 90
F25 / F26 M10x25 Renew screws
Jointing torque 56 Nm
Angle of rotation 90
2AZ
Suspension cross-brace in engine compartment, front
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M10x25 56 Nm
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M10x47 Renew screws
Jointing torque 30 Nm
Angle of rotation 90
3AZ
Connection, rear, to carrier support
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 28 Nm
4AZ
Connection, front, to connection, rear
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 19 Nm
5AZ
Engine compartment lid catch
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M8x20 11,8 Nm
6AZ
V-support to connection, front
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 19 Nm
7AZ
Air duct, lower, to vertical strut
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 19 Nm
8AZ
Air duct, lower, to carrier
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M8 8 Nm
9AZ
Air duct, upper, on lock support
F01 / F02 / F03 / F04 / F06 / F07 / F10 / F11 / F12 / F13 / F18 M8 8 Nm
10AZ
Trailing link/V-strut on side member
F07 / F11 / F12 / F13 M12 Renew screws
Jointing torque 100 Nm
Angle of rotation 90
11AZ
Trailing link to compression strut, rear axle
F07 / F11 / F12 M8 19 Nm
12AZ
Trailing link to cross reinforcement (rear end support)
F07 / F11 / F12 M12 Renew screws
Jointing torque 100 Nm
Angle of rotation 90
13AZ
Cross reinforcement (support, rear end) to rear end
F07 / F11 / F12 M10x22 38 Nm
14AZ
Cross reinforcement (support, rear end) to cross-member
F07 / F11 / F12 M10 38 Nm
15AZ
Torsion struts/stiffening plate to front axle support
F01 / F02 / F03 / F12 M10 Renew screws
Jointing torque 56 Nm
Angle of rotation 90
16AZ
Rear trailing link
F10 / F12 M10x40 Renew screws
Jointing torque 56 Nm
Angle of rotation 105
17AZ
Rear trailing link
F10 / F12 M8x35 Renew screws
Jointing torque 28 Nm
Angle of rotation 90
Appreciate 0
      03-10-2019, 11:05 AM   #5
beach48
Enlisted Member
4
Rep
32
Posts

Drives: 2013 F02 760LI
Join Date: Nov 2016
Location: Bristol UK

iTrader: (0)

https://www.newtis.info/tisv2/a/en/f...lines/1LoYYDX1


THE ENGINE IN PIC IS NOT A 760 ITS v8
Appreciate 0
      03-11-2019, 12:11 AM   #6
cowboy750
Enlisted Member
cowboy750's Avatar
United_States
0
Rep
37
Posts

Drives: bmw F02 750LI,E84 X1
Join Date: Apr 2018
Location: salinas,ca

iTrader: (0)

Quote:
Originally Posted by beach48 View Post
https://www.newtis.info/tisv2/a/en/f...lines/1LoYYDX1


THE ENGINE IN PIC IS NOT A 760 ITS v8
Thank you very much!!!!!!
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 02:14 PM.




7post
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST